A practical reference on Reversed-phase: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
This page was last updated on 2025-12-23 and is reviewed periodically as new material appears.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
| Parameter | Typical acceptance criterion | Notes |
|---|---|---|
| Resolution | ≥ 1.5 | Baseline separation of adjacent peaks |
| Tailing factor | ≤ 2.0 | Peak symmetry measure |
| Theoretical plates | > 2000 | Column efficiency indicator |
| Injection repeatability | ≤ 2% RSD | Relative standard deviation for replicate injections |
| Linearity | r² ≥ 0.995 | Calibration curve over the working range |
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Calmodulin-like protein 5 is a protein that in humans is encoded by the CALML5 gene. This gene encodes a novel calcium binding protein expressed in the epidermis and related to the calmodulin family of calcium binding proteins. Functional studies with recombinant protein demonstrate it does bind calcium and undergoes a conformational change when it does so. Abundant expression is detected only in reconstructed epidermis and is restricted to differentiating keratinocytes. In addition, it can associate with transglutaminase 3, shown to be a key enzyme in the terminal differentiation of keratinocytes. Human CALML5 genome location and CALML5 gene details page in the UCSC Genome Browser. Overview of all the structural information available in the PDB for UniProt: Q9NZT1 (Human Calmodulin-like protein 5) at the PDBe-KB.
The American Society of Plant Biologists (ASPB) is a non-profit professional society for research and education in plant science. It was founded in 1924 as the American Society of Plant Physiologists (ASPP); the name was changed in 2001. Membership in the society is open to any person from any country who deals with physiology, molecular biology, environmental biology, cell biology and plant biophysics or related issues. It has over 4,000 members worldwide. The society publishes the peer-reviewed journals Plant Physiology (1926–) and The Plant Cell (1989–) as well as ASPB News. The American Society of Plant Biologists also has partnered with the Society for Experimental Biology, and John Wiley & Sons to publish an online-only science journal Plant Direct. In 2000, it published the first edition of the textbook Biochemistry & Molecular Biology of Plants. The first President of the Society was Charles Albert Shull (1924–1925), with founder R. B. Harvey as Secretary-Treasurer. Other presidents of the Society include Harry Beevers (1961–1962), Aubrey Naylor (1960–1961), and Katayoon Dehesh (2021-2022). The first woman to be president of the society was Elisabeth Gantt (1988–1989).
Initial letters are used where there is no ambiguity: C cysteine, H histidine, I isoleucine, M methionine, S serine, V valine. No other amino acids in this set begin with each of those letters. Where arbitrary assignment is needed, the structurally simpler amino acids are given precedence: A alanine, G glycine, L leucine, P proline, T threonine. For example, alanine is simpler than arginine or asparagine, the other amino acids starting with "a". F PHenylalanine and R aRginine are assigned by being phonetically suggestive, W tryptophan is assigned based on the double ring being visually suggestive to the bulky letter W, K lysine and Y tyrosine are assigned as alphabetically nearest to their initials L and T (note that U was avoided for its similarity with V, while X was reserved for undetermined or atypical amino acids); for tyrosine the mnemonic tYrosine was also proposed, D aspartate was assigned arbitrarily, with the proposed mnemonic asparDic acid; E glutamate was assigned in alphabetical sequence being larger by merely one methylene –CH2– group, N asparagine was assigned arbitrarily, with the proposed mnemonic asparagiNe; Q glutamine was assigned in alphabetical sequence of those still available (note again that O was avoided due to similarity with D), with the proposed mnemonic Qlutamine.
Formation of the Quinonoid Intermediate PLP acts as an 'electron sink' absorbing delocalized electron density during the reaction intermediates (countering the excess electron density on the deprotonated a-carbon). PLP facilitates the enzyme activity, increasing the acidity of the alpha carbon by stabilizing the conjugate base. The PLP-stabilized carbanion intermediate formed is the quinonoid intermediate. Tyrosine and PLP stabilized 3C-Ring formation PLP and Tyrosine stabilize negative charges during deprotonation. Tyrosine attacks the sulfur bound carbon, allowing S(CH3)(Ado) to leave, and during ring formation, Tyrosine leaves. Note inhibitors AVG and AMA bind PLP to form a ketimine and oxime respectively (whose reverse reactions are much less favorable) and prevent the ACC synthase catalyzed reaction with SAM.
Sources: en.wikipedia.org
Ansuvimab, sold under the brand name Ebanga, is a monoclonal antibody medication used for the treatment of Ebolavirus (Zaire ebolavirus) infection. The most common symptoms include fever, tachycardia (fast heart rate), diarrhea, vomiting, hypotension (low blood pressure), tachypnea (fast breathing) and chills; however, these are also common symptoms of Ebolavirus infection. Ansuvimab was approved for medical use in the United States in December 2020. It is on the World Health Organization's List of Essential Medicines. Ansuvimab is composed of a single monoclonal antibody (mAb) and was initially isolated from immortalized B-cells that were obtained from a survivor of the 1995 outbreak of Ebola virus disease in Kikwit, Democratic Republic of the Congo. In work supported by the United States National Institutes of Health and the Defense Advanced Projects Agency, the heavy and light chain sequences of ansuvimab mAb were cloned into Chinese hamster ovary cell lines and initial production runs were produced by Cook Phamica d.b.a. Catalent under contract with Medimmune.
Aaron R. Wheeler is a Canadian chemist who is a professor of chemistry and biomedical engineering at the University of Toronto since 2005 with cross-appointment at Institute of Biomedical Engineering and Terrence Donnelly Centre for Cellular and Biomolecular Research. His academic laboratory is located at Lash Miller Chemical Laboratories and Terrence Donnelly Centre for Cellular and Biomolecular Research at the University of Toronto. In 2005, Wheeler was appointed as assistant professor and Tier II Canada Research Chair then promoted to associate professor in 2010, full professor in 2013, and in 2018 he became the Tier I Canada Research Chair in Microfluidic Bioanalysis. Wheeler did his undergraduate studies at Furman University in Greenville, SC then he joined Stanford University from 1997 to 2003 to obtain his Ph.D. in chemistry under supervision of Richard Zare . Following graduation, he took a two-year NIH postdoctoral fellowship at UCLA till 2005.
Aminoacyl-tRNA synthetase enzymes consume ATP in the attachment tRNA to amino acids, forming aminoacyl-tRNA complexes. Aminoacyl transferase binds AMP-amino acid to tRNA. The coupling reaction proceeds in two steps: aa + ATP ⟶ aa-AMP + PPi aa-AMP + tRNA ⟶ aa-tRNA + AMP The amino acid is coupled to the penultimate nucleotide at the 3′-end of the tRNA (the A in the sequence CCA) via an ester bond (roll over in illustration). Transporting chemicals out of a cell against a gradient is often associated with ATP hydrolysis. Transport is mediated by ATP binding cassette transporters. The human genome encodes 48 ABC transporters, that are used for exporting drugs, lipids, and other compounds.
DeepMind is known to have trained the program on over 170,000 protein structures from the Protein Data Bank, a public repository of protein sequences and structures. The program uses a form of attention network, a deep learning technique that focuses on having the AI identify parts of a larger problem, then piece it together to obtain the overall solution. The overall training was conducted on processing power between 100 and 200 GPUs.
Affimer proteins were developed initially at the MRC Cancer Cell Unit in Cambridge then across two laboratories at the University of Leeds. Derived from the cysteine protease inhibitor family of cystatins, which function in nature as cysteine protease inhibitors, these 12–14 kDa proteins share the common tertiary structure of an alpha-helix lying on top of an anti-parallel beta-sheet. Affimer proteins display two peptide loops that can all be randomized to bind to desired target proteins, in a similar manner to monoclonal antibodies. Stabilization of the two peptides by the protein scaffold constrains the possible conformations that the peptides can take. This increases the binding affinity and specificity compared to libraries of free peptides, though can limit the target repertoire of Affimers.
Sources: en.wikipedia.org
Sedimentation equilibrium experiments reports the molar mass of analytes and their chemical equilibrium constants. The rotor speed is adjusted such that a steady-state concentration profile c(r) of the sample in the cell is formed, where sedimentation and diffusion cancel out each other. Ultracentrifuge Gas centrifuge Theodor Svedberg Differential centrifugation Buoyant density ultracentrifugation Zippe-type centrifuge Reversible Associations in Structural and Molecular Biology (RASMB -an Analytical Ultracentrifugation Forum) Analytical Ultracentrifugation as a Contemporary Biomolecular Research Tool. Archived 2002-08-04 at the Wayback Machine Gilbert-Jenkins theory Archived 2007-05-01 at the Wayback Machine Report on an ultracentrifuge explosion.
The source of ADP-ribose for most enzymes that perform this modification is the redox cofactor NAD+. In this transfer reaction, the N-glycosidic bond of NAD+ that bridges the ADP-ribose molecule and the nicotinamide group is cleaved, followed by nucleophilic attack by the target amino acid side chain. (ADP-ribosyl)transferases can perform two types of modifications: mono(ADP-ribosyl)ation and poly(ADP-ribosyl)ation.
ALK-positive ALCL occurs mostly but not exclusively in children and young adults and is slightly more common in males. Most individuals present with stage III or IV (i.e. advanced) disease. They evidence systemic symptoms including B symptoms such as fever, night sweats, and weight loss in 75% of cases; lymph node enlargement (90%) including those in the mediastinum (36%); and lymphomatous lesions in the skin (26%), bone (14%), soft tissues (15%), lung (12%), and/or liver (8%). Tumor cells are found in the bone marrow in up to 40% of the cases when immunohistochemical analysis is performed. Involvement of the central nervous system or a leukemia-like circulation of malignant cells in the blood occurs only very rarely. Most patients, including up to 90% of young children and adolescents, have circulating autoantibodies directed against the ALK fusion protein expressed by their tumor cells.
In Brazil, the Aeronautical Accidents Investigation and Prevention Center (CENIPA) was established under the auspices of the Aeronautical Accident Investigation and Prevention Center, a Military Organization of the Brazilian Air Force (FAB). The organization is responsible for the activities of aircraft accident prevention, and investigation of civil and military aviation occurrences. Formed in 1971, and in accordance with international standards, CENIPA represented a new philosophy: investigations are conducted with the sole purpose of promoting the "prevention of aeronautical accidents". In Canada, the Transportation Safety Board of Canada (TSB), is an independent agency responsible for the advancement of transportation safety through the investigation and reporting of accident and incident occurrences in all prevalent Canadian modes of transportation – marine, air, rail and pipeline. In China, the Civil Aviation Administration of China (CAAC) is solely responsible for all air investigations and safety inside the country after the split from the formal CAAC Airlines.
The overall fold of Acutolysin A is composed of a twisted β-sheet core flanked by α-helices, forming the characteristic metzincin architecture. Central to this fold is the conserved “Met-turn”, a methionine-containing structural motif that stabilizes the active-site configuration. The three disulfide bonds in AaH I (Cys117–Cys197, Cys159–Cys181, and Cys157–Cys164) are strategically positioned to maintain this fold under physiological conditions and to resist thermal or proteolytic degradation. These disulfide linkages play a crucial role in preserving the shape of the catalytic cleft, ensuring maximal enzymatic activity even in harsh extracellular environments. At the active site is the HELGHNLGLH metalloproteinase motif, which binds a catalytic zinc ion in a tetrahedral geometry. Three histidine residues coordinate the zinc atom, while the fourth ligand is either a water molecule or hydroxide ion, which acts as the nucleophile in peptide bond hydrolysis. The active-site cleft forms a deep groove that accommodates collagen and laminin fibers, aligning them precisely for cleavage. This structural arrangement explains the exceptional potency of AaH I in degrading basement membranes.
Sources: en.wikipedia.org
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.
System suitability tests are short checks performed before or during an HPLC run to verify instrument and method performance. They often include resolution, tailing factor, theoretical plates, and injection precision. Results must meet predefined limits for sample data to be accepted.
HPLC retention time alone cannot definitively identify an unknown substance. A match with a reference standard under identical conditions provides supporting evidence. Confirmation typically requires mass spectrometry, nuclear magnetic resonance, or another orthogonal technique.
HPLC separates and quantifies compounds in a liquid sample. Detectors produce a response proportional to the amount of a compound passing through the flow cell. Identification by retention time requires comparison with a known standard.