Everything below concerns precision. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Updated 2026-01-30. Numbers and descriptions here follow the published literature rather than marketing material.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Ash is the solid remnants of fires. Specifically, ash refers to all non-aqueous, non-gaseous residues that remain after something burns. In analytical chemistry, to analyse the mineral and metal content of chemical samples, ash is the non-gaseous, non-liquid residue after complete combustion. Ashes as the end product of incomplete combustion are mostly mineral, but usually still contain an amount of combustible organic or other oxidizable residues. The best-known type of ash is wood ash, as a product of wood combustion in campfires, fireplaces, etc. The darker the wood ashes, the higher the content of remaining charcoal from incomplete combustion. The ashes are of different types. Some ashes contain natural compounds that make soil fertile. Others have chemical compounds that can be toxic but may break down in soil from chemical changes and microorganism activity. Like soap, ash is also a disinfecting agent (alkaline). The World Health Organization recommends ash or sand as alternative for handwashing when soap is not available. Before industrialization, ash soaked in water was the primary means of obtaining potash.
In an effort to prevent incidents such as the disappearance of Malaysia Airlines Flight MH370, a new standard has been issued requiring all commercial aircraft to report their position every 15 minutes to air traffic controllers regardless of the country of origin. Introduced in 2016 by the ICAO, the regulation has no initial requirement for any new aircraft equipment to be fitted. The standard is part of a long-term plan, called the Global Aeronautical Distress and Safety System (GADSS), which will require new aircraft to be equipped with data broadcast systems that are in constant contact with air traffic controllers. The GADSS is similar to the Global Maritime Distress and Safety System (GMDSS) used for maritime safety.
In some reactions, protons and hydroxide may directly act as acid and base in term of specific acid and specific base catalysis. But more often groups in substrate and active site act as Brønsted–Lowry acid and base. This is called general acid and general base theory. The easiest way to distinguish between them is to check whether the reaction rate is determined by the concentrations of the general acid and base. If the answer is yes then the reaction is the general type. Since most enzymes have an optimum pH of 6 to 7, the amino acids in the side chain usually have a pKa of 4~10. Candidate include aspartate, glutamate, histidine, cysteine. These acids and bases can stabilise the nucleophile or electrophile formed during the catalysis by providing positive and negative charges.
APCs naturally have a role in fighting tumors, via stimulation of B and cytotoxic T cells to respectively produce antibodies against tumor-related antigen and kill malignant cells. Dendritic cells, presenting tumor-specific antigen to T cells, are key to this process. Cancer therapies have included treating the patient with increased numbers of dendritic cells or cancer-specific T cells. However, newer therapies have turned to genetically engineered artificial antigen-presenting cells designed to prime the immune system to attack malignant cells. Some artificial APCs are derived from human cells; others are acellular, containing MHC proteins, co-stimulatory molecules and the necessary peptides. The APC activator IMP321 is being tested in clinical trials to accelerate the immune reaction to eliminate metastatic breast cancer or melanoma. Antigen: protease degradation on YouTube – PMAP animation Antigen-Presenting+Cells at the U.S. National Library of Medicine Medical Subject Headings (MeSH)
Sources: en.wikipedia.org
Automated synthesis systems find new applications with a development of new robotic platforms. Possible applications include: uncontrolled synthesis, time-dependent synthesis, radiosynthesis, synthesis in demanding conditions (low temperatures, presence of specific atmosphere like CO, H2, N2, high pressure or under vacuum) or whenever the same or similar workflow needs to be applied multiple times with the aim to: optimize reactions, synthesize many derivatives in small scale, perform reactions of iterative homologations or radiosynthesis. Automated synthesis workflows are needed both in academic research and a wide array of industrial R&D settings (pharmaceuticals, agrochemicals, fine & specialty chemicals, renewables & energy research, catalysts, polymers, ceramics & abrasives, porous materials, nanomaterials, biomaterials, lubricants, paints & coatings, home care, personal care, nutrition, forensics).
Abraham White (March 8, 1908 – February 14, 1980) was a professor of biochemistry who made several important discoveries in his field during the middle of the 20th century and helped write a foundational textbook, Principles of Biochemistry, which was published in 1954. The book went through six editions before its authors retired. White was born in Cleveland, Ohio, to Morris and Lena White. His siblings were Essie and Julius ("Jay"). When he was about one year old, his family moved to Lafayette, Colorado, and then later to Denver. White earned his bachelor's and master's degrees at the University of Colorado and a Ph.D. degree in Physiological Chemistry at the University of Michigan in the laboratory of Howard B. Lewis. This was followed by a postdoctoral fellowship at the Yale School of Medicine with Hubert Bradford Vickery at the Connecticut Agricultural Experiment Station.
AAA proteases use the energy from ATP hydrolysis to translocate a protein inside the proteasome for degradation. Cdc48p/p97 functions as a hexameric AAA+ ATPase that provides the mechanical force necessary for substrate dislocation. Its activity is tightly regulated by ATP binding and hydrolysis, which induce conformational changes required for protein unfolding and extraction. The HbYX motif plays a crucial role in regulating this process by mediating interactions between Cdc48p/p97 and downstream effectors such as the 20S proteasome or specific cofactors (e.g., Ufd1/Npl4). This interaction facilitates substrate transfer from Cdc48p/p97 to the proteasome, ensuring efficient protein degradation. Given its pivotal role in protein homeostasis, Cdc48p/p97 has been implicated in a wide range of cellular processes beyond ERAD, including autophagy, mitochondrial quality control, and DNA repair. The dysregulation of its function, particularly through mutations affecting the ATPase domain or HbYX-mediated interactions, has been linked to neurodegenerative diseases and cancer.
Another strategy for site-specific amine conjugation to proteins is to replace lysine residues with arginine residues (LDVs). If all lysines are depleted then the only remaining free amine is at the amino terminus (N-terminus) of the protein. In the case where the protein is an antibody Fc domain, a recombinant LDV Fc can still be purified using protein A. LDV Fc proteins fused with short peptide targeting sequences can be used to deliver conjugated payloads, including nanoparticles, to specific cell surface proteins. The majority of ADCs under development or in clinical trials are for oncological and hematological indications. This is primarily driven by the inventory of monoclonal antibodies, which target various types of cancer. However, some developers are looking to expand the application to other important disease areas.
In its oxidized form, azurin (Cu2+Az) receives an electron from its redox partner and is reduced according to the following reaction: Cu2+Az + e− → Cu+Az The redox potential is 310 mV. The highly interconnected beta-sheet structure of azurin is strongly coupled with its electron-transfer center (the copper-binding side). Considerable experimental evidence exists to suggest that hydrogen bonds play a role in the long-distance electron transfer mechanism of azurin. Taken together, these observations suggest that electrons tunnel through the protein along its polypeptide and hydrogen bonds, making azurin a useful model system for studying long-range, intraprotein electron transfer (LRET).
Sources: en.wikipedia.org
. It is used as a measure of affinity, with higher values indicating a lower affinity. For the given equation (E = enzyme, S = substrate, P = product), E + S ⟺ k − 1 k 1 E S ⟺ k 2 E + P {\displaystyle E+S{\overset {k_{1}}{\underset {k_{-}{1}}{\Longleftrightarrow }}}ES{\overset {k_{2}}{\Longleftrightarrow }}E+P} k d {\displaystyle k_{d}} would be equivalent to k − 1 / k 1 {\displaystyle k_{-1}/k_{1}} , where k 1 {\displaystyle k_{1}} and k − 1 {\displaystyle k_{-1}} are the rates of the forward and backward reaction, respectively in the conversion of individual E and S to the enzyme substrate complex. Information theory allows for a more quantitative definition of specificity by calculating the entropy in the binding spectrum. The chemical specificity of an enzyme for a particular substrate can be found using two variables that are derived from the Michaelis-Menten equation. k m {\displaystyle k_{m}} approximates the dissociation constant of enzyme-substrate complexes. k c a t {\displaystyle k_{cat}}
Effective on new passenger cars sold in the United States after January 1, 1964. front outboard lap belts were required. On September 9, 1966, the National Traffic and Motor Vehicle Safety Act became law in the U.S., the first mandatory federal safety standards for motor vehicles. Effective in 1966, US-market passenger cars were required to be equipped with padded instrument panels, front and rear outboard lap belts, and white reverse (backup) lamps. In 1966, the U.S. established the United States Department of Transportation (DOT) with automobile safety as one of its purposes. The National Transportation Safety Board (NTSB) was created as an independent organization on April 1, 1967, but was reliant on the DOT for administration and funding. However, in 1975 the organization was made completely independent by the Independent Safety Board Act (in P.L. 93-633; 49 U.S.C. 1901). In 1967, equipment specifications by such major fleet purchasers as the City and County of Los Angeles, California, encouraged the voluntary installation in most new cars sold in the US of safety devices, systems, and design features including:
An insulin pump delivers insulin subcutaneously. The insulin pump body itself can also contain the algorithm used in an AID system, or it can connect via Bluetooth with a separate mobile device (such as a phone) to send data and receive commands to adjust insulin delivery. Algorithm The algorithm for each AID system differs. In commercial systems (see below), little is known about the details of how the control algorithm works. In open source systems, the code and algorithm are openly available. In general, all algorithms do the same basic functionality of taking in CGM data and based on predicted glucose level's and the user's personal settings (for basal rates, insulin sensitivity, and carbohydrate ratio, for example) then recommends insulin dosing to help bring or maintain glucose levels in target range. Depending on the system, users may have the ability to adjust the target for the system, and may have different settings to ask the system to give more or less insulin in general.
Cells of one type may release the 5(S)-HETE that they make to nearby cells of a second type which then oxidize the 5(S)-HETE to 5-oxo-ETE. This transcellular production typically involves the limited variety of cell types that express active 5-lipoxygenase, lack HEDH activity because of their high levels of NADPH compared to NADP+ levels, and therefore accumulate 5(S)-HETE, not 5-oxo-ETE, upon stimulation. This 5(S)-ETE can leave these cells, enter various cell types that possess 5-HEDH activity along with lower NADPH to NADP+ levels, and thereby be converted to 5-oxo-ETE. Transcellular production of 5-oxo-eicosatetraenoates has been demonstrated in vitro with human neutrophils as the 5(S)-HETE producing cells and human PC-3 prostate cancer cells, platelets, and monocyte-derived dendritic cells as the oxidizing cells. It is theorized that this transcellular metabolism occurs in vivo and provides a mechanism for controlling 5-oxo-ETE production by allowing it to occur or be augmented at sites were 5-lipoxygenase-containing cells congregate with cell types possessing 5-HEDH and favorable NADPH/NADP+ ratios; such sites, it is theorized, might include those involving allergy, inflammation, oxidative stress, and rapidly growing cancers.
Homopolymers of amino acids (such as polylysine) can adopt α-helical structure at low temperature that is "melted out" at high temperatures. This helix–coil transition was once thought to be analogous to protein denaturation. The statistical mechanics of this transition can be modeled using an elegant transfer matrix method, characterized by two parameters: the propensity to initiate a helix and the propensity to extend a helix.
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
HPLC separates and quantifies compounds in a liquid sample. Detectors produce a response proportional to the amount of a compound passing through the flow cell. Identification by retention time requires comparison with a known standard.